Bernard Reller
”Sleek and well-made. . . The most unobtrusive mechanism of its type on the market.”
Alan Revere, Revere Academy, San Francisco
Fine Jewelry for 75 Years
Call . . . 800-233-4820 . . .
to find a FOREVERFIT™ Jeweler
Bernard Reller |
Alan Revere, Revere Academy, San Francisco |
Fine Jewelry for 75 Years Call . . . 800-233-4820 . . . to find a FOREVERFIT™ Jeweler |
| INFORMATION FOR PROFESSIONAL JEWELERS |
|
 |
EASIEST, QUICKEST INSTALLATION (OR WE WILL DO IT FOR YOU!)
IF YOU CAN HALF-SHANK A RINGYOU CAN INSTALL ForeverFit™.
EASIEST FOR YOUR CUSTOMERSNO JIGS OR SPECIAL TOOLS ARE NEEDED. SLIPS ON . . . SLIPS OFF.
EASIEST TO INSTALLONLY NOVICE SKILLS REQUIRED.
LONGEST LASTING
NO CATCHES TO WEAKEN OR BREAK.
|
|
|||||||
 |
BEST VALUE
MOST COMPETITIVE PRICING.
BEST OF ALL:
INSTANTLY ADJUSTS TO A CHANGING RING SIZE
|
Click the button below to join our Referral Registry. |
 |
|
Already a FOREVERFIT™ Jeweler? Join our Referral network! Wholesalers . . . Call for Jobber pricing. 800-233-4820 |
 2.5mm, 4mm, 6mm |
Three Widths: 2.5mm, 4mm and 6mm Sizes: 5 through 12 (whole sizes) (Adjusts down 3½ sizes)
Metals: 14K Gold, Yellow and Bright White
18K Gold, Yellow and Bright White
Platinum Sterling |
 |
| Tech Tips for Jewelers | ||||
| Reller’s FOREVERFIT™ Self-Sizing Shank is about as easy to install as “half shanking” any ring. Simply measure your customer’s ring size normally (a comfortable slide over the knuckle allows for a little future growth). Next, if necessary, reshape the customer’s ring to this ring size and remove the bottom of the shank at the point where the cross section best matches the FOREVERFIT™ (Available widths- 2.5mm, 4mm or 6mm). Remove the corresponding top section of the FOREVERFIT™, solder the customer’s ring top to the FOREVERFIT™ shank and polish the joint. It’s as simple as that! |
||||
|
|
 |
|
|
||||
| No solder is used in the original construction of the FOREVERFIT™ so the mechanism won’t “freeze up.” The Stainless Steel spring “floats” under the cradle and may be removed during the soldering process, or you can protect it as you would a sensitive stone, with Kool Jool or wet tissue. Do not compress the spring while soldering, as this concentrates the heat. The stainless steel spring is not affected by a brief immersion in the pickle solution. Note: The FOREVERFIT™ components are a precision fit; so do not attempt to
alter the FOREVERFIT™ shape before or after assembly. Encourage your customer to come in frequently for a “FREE ULTRASONIC CLEANING!” and avoid loading up the mechanism with soap, soil, grime and dirt. Down the road, complete disassembly of the FOREVERFIT™ is easy. The .021 pins used in the assembly are a press fit. They may be pressed out with a mini arbor press or simply reverse a #77 or smaller drill bit in the chuck of a small drill press. Leave about a ¼” or less of the drill shank extending, and presto — you have an arbor press for this and other similar tasks around the shop. The pins may be replaced with wire drawn full hard to .021, tapered for insertion, and then trimmed flush. A little burnishing helps “rivet” the pin in place the second time around. Springs may be removed and reshaped to increase or decrease tension, as desired. When replacing a spring be certain that the ends are polished smooth with no sharp edges to hang up. Replacement springs and component parts are available from your supplier or directly from Reller. Display Tips
A sample FOREVERFIT™ CZ Solitaire in Sterling Silver is available from your supplier or Reller at a nominal charge. The sample comes with a mahogany ring stand and counter display for $30. Otherwise, a FOREVERFIT™ Self Sizing Ring is very effectively displayed by reversing a standard “finger” type ring stand and loosely sliding on the FOREVERFIT™ showing the mechanism in action. |
||||
 Click to return to top Return to the ForeverFit™ home page. |
||||
|
Tech Tips for Springs (for Jewelers) |
||||
|
1. The leaf spring “floats” in the channel of the ring shank and may be removed for ring cleaning and adjustment of the tension. 2. The spring material is supplied with a medium temper. It may be shaped on a ring mandrel to increase or decrease the upward curvature and therefore increase or decrease spring tension to suit customer preference.  3. When replacing a spring it is important to use the correct length spring for the customer’s ring size. One particular length spring will perform properly over two consecutive ring sizes. 4. Always ensure that the ends of the replaced spring are smooth with no burs, corners are rounded and polished smooth. This is especially critical when cutting a new spring from Reller supplied spring material. A bur here can act like a tiny gravier and dig into the soft gold of the channel and prevent the spring end from sliding freely. 5. Before Replacing a Spring check to see that the Mechanism is free of debris and soap build-up and that the channel is smooth. After ultrasonic and steam cleaning, a drop of light machine oil applied to the mechanism restores lubrication minimizing wear. 6. The finger cradle should move vertically in the plane of the ring with a minimum of sideward play. One millimeter is normal. Also, the cradle should not rock or tilt, but remain parallel to the bottom of the shank within about 10 degrees. Excessive play may permit the spring to pop out. Extensive play often indicates that the ring has been worn in an abrasive environment or received a damaging blow. Quite often side-play can be removed by gently squeezing the channel to close it up a few thousandths, taking care not to bind the sliding hinges. This technique can also work on the cradle. If necessary, replacement parts are available from Reller. Making You Own Springs from Reller Supplied Spring Material 7. Specifications — 2 1/2 mm or 4 mm width; use 2 mm spring stock 6 mm width; use 4 mm spring stock Spring Length — Ring Size Length 4 15mm 5, 6, 7 17mm 8, 9 18mm 10, 11 19mm 12 20mm |
||||
|
Available as Adobe Reader File! You can Download Information about FOREVERFIT™ Tech Tips Tech Tips for Springs FOREVERFIT™ Information Sheet Counter Display Card 
|
||||
FORVERFIT™ Information, Tech and Jeweler Finder Hotline 800-233-4820 9:00 a.m. - 5:00 p.m. Eastern Monday - Friday |
||||
E-mail us: tech @ foreverfitrings.com |
| Ever Changing Ring Size?
For women of all ages — Independent research shows that 70% of all women will benefit from the self-sizing feature. No need to resize.
Engagment and Bridal? No need to stop wearing precious rings during pregnancy.
Arthritis? Loss of Manual Dexterity? Superior “ease of use!” Simply slips on and slips off. No small parts to manipulate, pinch, or break off. FOREVERFIT™ Fits!
Sense of Security? Precious rings can’t come open unexpectedly causing loss of a valuable stone or heirloom.
Durability? Extremely durable! The mechanism does not wear out. Unlike some competing products, FOREVERFIT™
Sizing? No complicated sizing required. FOREVERFIT™ recommends a loose fit over the knuckle, especially if knuckle growth is anticipated.
Installation? Simple and Quick.. No special tools or fixtures are necessary. FOREVERFIT™ Simplicity.
Options? 
FOREVERFIT™ comes in three widths, 2.5 mm, 4 mm, and 6 mm, and sizes 5 through 12
and is available in 14K, Bright White and Yellow . . . 18K, Bright White and Yellow . . . Platinum, Palladium, and Sterling. Cost? Competitive pricing, often well below our competitors.
How to Purchase? Directly from FOREVERFIT™ or through most major Findings Houses..
Guarantee? The best in the business! If you are not 100% satisfied, return the FOREVERFIT™ Self Sizing Ring.
Want to know more about FOREVERFIT™? E-mail tech @ foreverfitrings.com and we'll tell you all about it!
|
| Go to the RellerGold Home Page |
The designs contained in this site is copyright protected. It may not be used without prior written consent from Reller, Inc., or its partner companies.
|
